• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

70 rr steering column/coupler separated

rose heiden

Rosebud
Joined
Dec 26, 2020
Messages
31
Reaction score
29
Location
florida
hey, we bought a 70 383 rr a month ago. the steering wheel was grinding some so we removed steering wheel to inspect upper bearing and also noticed shaft at end of the column housing didn't have a bushing. Also noticed steering knuckle cap was loose. long story short while reinstalling the steering wheel the column separated from the knuckle housing. can't get it back together. any ideas on how to fix it? 32968-4d2a14b3da5f5610e709f7892ada9433.jpg
 

ACME A12

Plaid Sport Coat Wearing Moderator
Staff member
Joined
Nov 4, 2008
Messages
13,671
Reaction score
824
Location
New Port Richey, FL
The dowel pin is missing, worn, or incorrectly installed. Otherwise it wouldn't have come completely apart.

The assembly is spring loaded. It might be easiest to remove the roll pin and and slide the coupler body off of the steering box, put it back together, and then slide back on the steering box. Here's an exploded view diagram to show you what you are looking at. Make sure that you get the shoes correctly oriented when you slide it back into the body or it will have unwanted slop in it.
735_steer-coup_low_res.jpg
 

rose heiden

Rosebud
Joined
Dec 26, 2020
Messages
31
Reaction score
29
Location
florida
The dowel pin is missing, worn, or incorrectly installed. Otherwise it wouldn't have come completely apart.

The assembly is spring loaded. It might be easiest to remove the roll pin and and slide the coupler body off of the steering box, put it back together, and then slide back on the steering box. Here's an exploded view diagram to show you what you are looking at. Make sure that you get the shoes correctly oriented when you slide it back into the body or it will have unwanted slop in it.
View attachment 33557
The dowel pin is missing, worn, or incorrectly installed. Otherwise it wouldn't have come completely apart.

The assembly is spring loaded. It might be easiest to remove the roll pin and and slide the coupler body off of the steering box, put it back together, and then slide back on the steering box. Here's an exploded view diagram to show you what you are looking at. Make sure that you get the shoes correctly oriented when you slide it back into the body or it will have unwanted slop in it.
View attachment 33557
thanks. that's what we figured was the answer. should we buy a new coupler kit? when we put coupler body back onto the steering shaft how do we get the coupler to meet with the steering box, since the telescoping steering shaft isn't telescoping very well?
 

quikbird

Well-Known Member
Joined
Mar 1, 2014
Messages
3,229
Reaction score
1,020
Location
Sarasota, florida
If it doesn’t line back up something in the column or where it attaches to firewall is not set up correctly. Just have to go right down the line till find the problem. I can tell you from experience it is definitely a pain.
Ps. The final roll pin goes in after installed on the steering box. Don’t ask how much I’ve worked with this damn roll pin
 

Roadtrip

Well-Known Member
Joined
May 12, 2017
Messages
156
Reaction score
176
Location
Alberta
Pretty sure Earlier ones (67, 68, early 69) didn’t have the roll pin to. But being a 70 it should have one.
 

mopar jack

Well-Known Member
Joined
Jul 24, 2019
Messages
71
Reaction score
66
earlier couplings may not have the dowel pin to hold the internals but must have a roll pin to fasten the coupler to the steering box. I recommend you pull the complete column, clean and rebuild as needed and rebuild the coupling. There is a good video on columns on E-bodies.org. I always recommend the clamp that chrysler used in their TSB. see link. 4881871-SteeringColumnTSB (5).pdf
 

Russ69Runner

Well-Known Member
Joined
Aug 4, 2016
Messages
7,696
Reaction score
3,231
Location
Lake Wales Fl.
Saw a coupler that goes over that one. Almost bought one but rebuilt the hole steering column. I would do the same with that one.
 
Back
Top