Search results

Hello fellas. A couple months ago, I purchased a Hobart Handler welder. I've been wanting to learn how to weld for years. I would really appreciate any tips/Do's and Don'ts from you guys who weld. I need a table to weld on, my wooden work bench in the garage won't cut it. I was thinking on using...

Ok Fellas, here's one you don't see everyday. It's not mint, but it's blank.

When I picked up my mail this morning on my basement door landing (old house, mail slot in side door) I saw a corner of the latest Mopar Action magazine poking out. When I picked it up and looked at the cover, I immediately developed a burning sensation in my eyes! On the cover is the "Million...

Hi fellas, Do any of you have exhaust manifolds you would sell? Left Side # 2843992, or #2951865 Right Side # 2806900, or # 2899879 Let me know if you got 'em. Thanks! Harry

Do any of you have a decent set of 4 you wanna sell?

So, will this company see a bump in sales as a result of this show season? http://www.classicautoair.com/?q=68_70_Mopar+B-Body_Air_Conditioning_Mopar_AC.html

Ok, so which one of you guys drove the farthest to get to Carlisle this year? I backed out and I'm 3.5 hours away. Was it you Steve? I salute all you guys for making the trip. Let's give recognition to the man who drove the farthest in the BRUTAL heat!!!

So the filler tube on the 727 I purchased last week had pipe thread tape around the bottom of the filler tube to keep it snug. Well, I removed that along with the pan and filter to inspect what I just bought. Now the filler tube is kinda loose, it still has the little rubber "O" ring, and the...

I have the choice between two different 727's. I will be buying one for my 383 Scamp project. Both are $150 obo and both owners say they were running when pulled. Ironically, both are from guys who demo derbied but both said neither was used - they sound honest. They were just pulled from the...

So for my 8.75 swap in my '75 Scamp, I purchased a used 741 open case with 3.55's. I replaced the pinion seal, the gears looked good, I measured the backlash and came up with .010" (not bad for used gears). After installation, the rear whines. :brickwall: Not a howl and no grinding sounds...

Do any of you guys know what doughut spare I could look for in the boneyard that I could use on my BBP '75 Scamp? (5 on 4.5) I want to have a spare tire that will fit flush in the tire well in the trunk that could get me to the next exit on the highway.

So I installed the new gas tank that the previous owner included in the deal with the '75 Scamp I bought last Fall. I now need a ground strap. I ordered one but it was the short one (3 1/2") - I need the longer one. I rigged 1/2 a speaker wire with allegator clips for a temp. Any ideas on what...

I am replacing my gas tank (a new one, in the box, came with the Scamp when I bought it last Fall). Currently, it's a 225 car, within the next year, I am installing a 383 / 727. I want to install a new 3/8" sending unit instead of the stock 5/16" since I will be replacing the fuel lines with 3/8...

I've always done the RR, LR, RF, LF - brake loose the bleeder and have someone in the car pump the brakes. I read about gravity bleeding - where you fill the master cylinder and open all four bleeders. How do you do it?

Have you been reading how much credit this dipshit is taking? Obama is acting as if he killed Bin Laden with his bare hands! Pathetic.

I have used a C-clamp to replace U-joints, but it has been a while. Any tips you guys can offer would be appreciated. I have a bench vise that I was going to rest the ears of the driveshaft on to remove them by pounding them out. I don't own a press.

As I wait for the correct wheel cylinders to arrive..... Ok, heres another brake question. Which side does the star wheel adjuster go? One thread is left handed, the other right handed thread. I think mine were installed incorrectly last time someone changed the rear shoes. The right handed...

The wheel cylinders I removed on the rear of my Scamp had pistons in them with a socket/indentation on the face. The new wheel cylinders I bought have a flat face on the piston face. Can I still use the pins/links from my old WC? The pin/links (whatever you wanna call 'em) are curved at the end...

Ok, please give me your thoughts fellas. So I pulled the 7.25 and installed the 8.75 in my Scamp. The measurements for the axle centerline to the yoke center line for an 8.75 is 12.35" The measurements for the axle centerline to the yoke center line for an 7.25 is 10.09" To me, this means I need...

WOW. I am starting my 8.75 swap in my '75 Scamp. I want to use the packing plates from the 7.25. I can not remove the axle. No clips on these according to my '75 FSM, How the hell do you get these off? I am still working on the left side. Seems pressed in - I know it isn't. I removed the 5...