• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Recent content by OutLawBiker

  1. OutLawBiker

    Steering shaft rag joint and coupler replacement

    Hey Fellow Road Runner Lovers, I need to replace my rag joint and steering coupler on my 73 Road Runner. I understand there is a small shaft connected with u-joints on either end available as an upgrade. Does anyone know where to get one and possible part number? 727 floor shifter power steering...
  2. OutLawBiker

    Out of Time

    Hi Everyone, I lost timing on my 1974 Ply Road Runner. Here are the particulars LA360 Bored 30 over Cam .472 Lift 296 Duration 106 L/C 340 X Heads 1968 Edelbrock 7676 Air Max Intake Holley 750 Dual Feed Single Pump Vacuum Secondaries Stage 2 Torque Flight 727 Manual Valve-body Custom Headers...
  3. OutLawBiker

    Greedy Incompetent Transmission Shop-Possible Spun Crank Bearing

    droptop, Good advice- How can I be sure that the transmission caused my engine issues? What should I look for?
  4. OutLawBiker

    Greedy Incompetent Transmission Shop-Possible Spun Crank Bearing

    Old Angry White Guy, Hadn't thought about that since I paid him for a new one-I'll check it out though. Another reason is it quieted down a bit when it warmed up some.
  5. OutLawBiker

    Greedy Incompetent Transmission Shop-Possible Spun Crank Bearing

    I drove in with the almost new 1800 stall and brought him the 3000 stall I had at home. The problem was the 3000 stall was internally balanced. The tranny shop took the weight off the 1800 stall and weld it to the 3000 stall therefore ruining them both.
  6. OutLawBiker

    Greedy Incompetent Transmission Shop-Possible Spun Crank Bearing

    Thank you, Russ, I appreciate your response. I don't lose power what happens is lack of real power because the transmission is holding back the engine but not because it's slipping. You can feel the motor is trying to get there, but the tranny is holding it back. 2nd gear is good until I shift...
  7. OutLawBiker

    Greedy Incompetent Transmission Shop-Possible Spun Crank Bearing

    1973 Plymouth Road Runner LA 360 30 over 340 X Heads 1968 Edelbrock Air Max Intake Manifold Holley 750 Dual Feed Single Pump Vacuum Secondaries Custom Headers Uses* Street / Drag 1/4 Mile After I picked up my car from the transmission shop- Developed what sounded like I spun a crank bearing-...
  8. OutLawBiker

    360 LA Installing 340 X Heads-Hi Pro Mods

    Thanx for the direction to Summit Racing Russ - The guy I talked to wasn't old school. I'll check back tomorrow. Rich the dual points' distributor concept is great I'm looking into that-also the ultra-thin cooper head gasket as well. Thank you both for your help Important note:Following the 340X...
  9. OutLawBiker

    360 LA Installing 340 X Heads-Hi Pro Mods

    Hey Everybody, In my 1973 Road Runner I am installing 340 X Heads on my 360 LA engine and would love any advice on installation and high performance tricks... 73 Road Runner 360ci LA version 570 CFM dual feed single pump Holley carb. Edelbrock Performer intake manifold MSD Ignition and MSD...
  10. OutLawBiker

    FOR SALE 727 Transmission

    Howdy Russ, I know it's been a minute since you posted this 727 Tranny Curious-is this 727 for a small block? What is the torque convertor stall rating? R U negotiable on price? It would have to cross the entire country to zip code 97501 hinging on the final determination following "the...
  11. OutLawBiker

    SOLD beep beep horn w/ small bracket

    Curious-Still have your BEEP BEEP horn for sale? If YES would ship to 97501 Please price with all shipping cost. Thanks for your time...
  12. OutLawBiker

    SOLD two speed wiper motor

    Howdy, Curious - if you still have this component? R U negotiable? Possible ship to 97501 Thank you for your time my friend
  13. OutLawBiker

    FOR SALE Hughes 3000 Hi Stall HD s/b 727 24 Spline Torque Conv.

    For Sale: I have a slightly used (1 short season) 8 passes. Hughes Hi Stall 3000 RPM Small Block 727 24 Spline HD Torque Converter $525.00 Original Price My Sale Price only $295.00 You pay for all shipping charges
  14. OutLawBiker

    Headlamps

    HI, AFTER READING THIS THREAD I AM COMPELED TO ASK A QUESTION CONCERNING MY 73 RR. I JUST INSTALLED A PAINLESS WIRING HARNESS # 101427 21 CIRCUIT. I NEED TO KNOW ON THE HEADLIGHT SWITCH WHAT WIRES GOES TO WHICH OF 7 MALE CONNECTORS. THE PLASTIC HOUSING FOR THE SWITCH IS NO LONGER. PLEASE...
Back
Top