Search results for query: *

I use B&M Trick Shift. My transmission is a B&M 727 with a custom torque converter, that is mounted behind a 1000 hp Indy engine, and the Trick Shift works extremely well. Zero slippage with solid shifts... no jerking, just solid shifts. I also have the Gear Vendor unit mounted to the backside...

Back in the day (the late 60's and early 70's) we'd often add a second breather tube directly off the filler tube and, using a T-fitting, tie into the stock breather tube, thereby eliminating any fuel sloshing up through the original breather tube and onto the ground in front of the rear...

I have a Griffin Exact-Fit radiator, with dual 12-inch electric fans and a custom stainless shroud in my 69 Road Runner It does an excellent job maintaining an acceptable temperature. I've had it out in scorching heat (100 +) with the AC on and the temp will run between 200 and 215. The engine...

I just loved viewing all your photos. This is the beginning of quite an adventure. Have patients and absolutely have a plan and have fun!! My Road Runner had more rust than paint and at least twenty pounds of body filler plus a completely worthless drivetrain. That was eight years ago and now...

My fuel vapor canister is located in the trunk next to the amp and behind the speaker casing. I have two separate vapor tubes (from the upper portion of the tank and from the fuel filler tube) that connect via a T-fitting, then go into the canister, then exits the canister, through the trunk...

Correction to my recent post. The power steering setup is mounted immediately below and next to the AC compressor (I've attached same photo for clarification).

I have a Borgeson steering box that bolts right in; an Ididit tilt steering column; belt driven power steering mounted directly behind the AC compressor. You can get all this as a kit or piece it together. With exception of the steering box and column, I went the kit route to be sure everything...

It's all about compression, especially if you reside in California, where premium is only 91. I have a 572 Indy Head Max Wedge 750 HP and 775 lbs. of torque. It's 10.5.1 and runs great on California premium. Fuel is fed through an EZ FAST 2.0 system with eight injectors. It's a solid lifter...

You must be kicking yourself for parting with, what looks like, a nice Road Runner. My first 69 Road Runner was purchased brand new in November of 1968 for a whopping $2974 out the door. It was an ivy green post car with the decor' package. I had to part with it in 1971 due to new regulations...

There are several different outside mirrors versions. An optional mirror setup was dual mirrors with the driver-side being adjustable from the inside by a cable. The photo is the setup with the driver-side adjustable mirror.

I am getting ready to level the front and rear on my 69 Road Runner (note: it's got the hemi leaf springs - six leaf springs on the driver side and 7 on the passenger side). The passenger front is approximately 1/2 inch too low, and the rear passenger side is also approximately 1/2 inch too low...

Your Road Runner brings back some fond memories. I just wrapped up my 69 Road Runner project. Ivy green post car with black horizontal stripes and all black leather interior. Back in November of 1968 O decided I’d buy a Road Runner. I came close to buying a used 68 black Hemi car with low miles...

After a two-year “time-out” from this site I have re-joined. Have finally complete a seven (+) year restoration/build project of my 69 Road Runner. I recently discovered the fuel gauge does not work (Needle moves back and forth from empty to full)!!?? All electrical tested and is good. I‘ll be...

When I redid everything on my 69 Road Runner, it included a complete re-wiring of the entire electrical system (front to back, engine bay and under dash). The shop where the build took place said because it was a complete renovation and upgraded system, everything had changed.

The ballast resister you are referring to is part of the original stock electrical system where gobs of amps were passed through the amp gauge and would typically be the culprit for under dash fires. Most of us who have significantly upgraded our electronics, including the addition of a volt...

68-70 ALL HAD THE BIRD DECAL ON THE FRONT FENDERS

Agree on just welding the backside and running a bead on the front then grind it down and that is all that needs done

I use Joe Gibbs 15-50 Racing oil. A lot of drag racers use this same oil, plus I know of a bunch of engine builders that also recommend it. I'm not saying it's the best oil on the planet, but it is a good oil for street and strip driving. My engine is a 509 stroker and runs between 200 and 220...

So you are going with aftermarket gauges, but no radio? After going through all kinds of gauge configurations, including adding a clock where the option for a clock or tach would go, and a four gauge holder below the dash, I finally decided just how ridiculous the whole setup looked, so I...

I'm running a 509 stroker; 275/60/15 rear and 235/60/15 front. Gears are 3:23 with a Detroit Truetrac and Gear Vendor Under/Overdrive unit. Overall it works out just fine. It launches solid and quick and cruises at 75 mph at 2600 rpm's, so you can have your cake and eat it too!!