Search results

So I picked up a couple of the 833s with the bolt on rear flange. IDK what years thinking pre 66. Can you cut off the threaded stub on the output shaft and use them with the slip yolk type shaft??

Where can I buy the clips that hold the molding at the top of the windsheild/ head liner. I got some from a vendor but they junk.Looking for NOS. Any leads?? Thanks.

Well I got a used pair of these little buggers on the cheap. The housings are nice but the guts are shot. I seem to remember seeing them for sale somewhere like E-bay. A recent search turned up nada. These units are the ones that have a set screw to hold it together and not the ones with the...

Well I am installing the headliner in my 68 post car. I am to the sail panel area and am wondering if it takes a board for the material to attach to?? I see them listed in the Classic book but dont see how they would attach. It looks like the 69s have a metal bracket. Am I missing this bracket...

All panels are in primer and rear window and trunk are repaired. Time to prep and seal the body. Lots of sanding in my future.

Howdy folks, I am getting the top end together on a 440 and have Isky adjustable shaft rockers. They have solid spacers and shims. I see them on Ebay with springs but I think using the spacers and shims would be better. Looking at the rocker body at the pedestal area do the shaft hold downs keep...

Ok folks, I want to change all the studs F&R. 11in drums all around. I would like to go with the longer ones from Moroso-Moser ect. Anyone have a part # or the knurl diameter? Or should I just knock one out and measure? Are front and rear different? Thanks.

Well plans changed, Instead of 383 am going 440. Got a 67 block and a set of 906s that are fresh. KB shows pistons with a reverse dome step head piston,one with a 075 step and a 125. Anyone have any experience with these slugs,recomendations. Pro con ? This is what my guy is saying to use. Thanks.

I have the tag but it was not installed when I got the car. Could someone please supply a pic of correct placement. The engine compartment has been painted and I cant seem to find the holes. Thanks.

Howdy Folks, The 8 3/4 I have is a 742 323 open unit. I have a 741 with a sure grip and will swap the ring gear to the SG case. Question is the Suregrip came without the end play buttons. I ordered a set and they come with what looks like a long rivet. Do you just install the 2 buttons then the...

Howdy all. I have a trunk panel off a Satelite I want to use on my R/R. Can anybody suggest a color for he red painted part. Picked up a rattle can of Duplicolor Chrysler Flash Red DSCC351. Will it be close or are there better options ??? Thanks.

Howdy All, Where can I get the bushing that connects the arm on the motor to the linkage? I have what I think is the retaining clip.

Like it says I am rebuilding my column. The service manual says to bend the reverse lite switch pin out of the way and it is not reusable.Well the pin is not even there, the switch is though. This looks to be a NOS only piece, cant find one anywhere. Anybody run into this before and have a...

Well better late than never.Swapmeet,Car show and Races @ Woodburn Oregon this Sunday.All Mopar except for the Races. See Ya there.

So my 68 has the dash with 3 speakers. I just found the grills for the outer speaker. Question is what will fit in all 3 spots? Maybe Best Buy has something that will fit.I also have the crossover/ splitter harness but more than likely wont use it. Did this setup come with any kind of fader...

I am a retired ASE Master Tech. My current ride is a 68 Bronze Metalic Road Runner, under construction. I had and lost to the big D a 70 Charger 500.So I have been into Mopars and all makes and models from the glory days. Cars I have had and sold, 67 GTO, 69 GTO, 70 340 Duster, couple of 69-73...