Search results

Anybody have experience with AMD's door and QTR window glass. I have heard the curvature on some glass doesn't match the originals. Wanted to make sure first before buying. Thanks.

My roller assemblies on my '70 RR Hardtop are frozen. Started looking at it and is pretty easy to take them apart to clean and lubricate. The main issue is the flat plate that secures the ball stud and the spring clip. It is held on by two rivets. If you grind the rivet heads off and punch out...

I have a '70 RR hardtop and was missing the SS trim between the qtr glass and door glass. This piece actually mounts on the door glass. I bought a L&R trim from a salvage yard last week. As luck would have it, I found the ones that came with the car when the package arrived. I am not saying the...

I have managed to figure out what every hole and cutout is for on my '70 RR. EXCEPT for one! It is a 4-speed, w/ air grabber, no a/c, manual brakes and steering, Rallye dash w/ a 440+6. The hole I cannot figure out is stuck between the speedo hole (7/8") and the oval cut out for the clutch...

I am rebuilding the steering column on my '70 RR with floor shift and manual steering. The question is which countersink on the shift tube does the shift housing set screw go into? If I push the shift housing as far down as I can on the shift tube, the set screw hits as shown in the first...

Getting ready to assembly the entire air grabber assembly and then install the box on the hood. Question is what sequence do you do this in order to install decals on the side of the lid off the car. It would be difficult to install these triangular decals if the lid is on the hood. The clevis...

I have L&R reverse light housings off of a '70 RR. They are in good original condition, work perfectly and ready to be cleaned up and used. The left housing has a new pigtail end on it as the original end was damaged. The new end was soldered together with heat shrink to seal the repair...

Looking at the recent thread for turn signal bumpers made me think about the problem I had with my '70 RR hood wedge bumpers. There are (4) mounted on either side the fenders. Every one I have tried are way short of contacting the hood when it is closed. Like about 3/16" too short. If they don't...

I bought my '70 RR mostly disassembled and some of the detail items are hard to figure out. Like the jack assembly in the trunk. Does anybody have a picture of how the jack is stored? I think I have all of the correct hardware, just need help to see how it goes together. I have two bolts that...

My question is if the air cleaner lid is painted orange on BOTH sides or just on the top from the factory? If just the top surface, I would assume the underside is semi gloss black like the base? BTW, I have the correct orange color. Thanks.

Just repainted the headlight door on the '70 RR and turned out better than I thought it would. I used spray paint from 8774paint1.com and worked out well. This uses the light and dark Argent paint. Nice paint, but be prepared to shake the can constantly as you spray as it settles quickly. Also...

I am confused when you use the 9-1/2” long armrest pad and when you should use the 13” long pad for the front. My RR was disassembled when I bought it and have no idea which it had. It is a ’70 RR hardtop with the deluxe interior and bench seats. I know you have to have the matching length base...

Wanting to confirm what three nuts to use to attach the drivers vent box to the cowl. The ones I have are the stamped metal “speed nuts”. Is that correct? Thanks.

I have seen in pictures that there were clips on the defrost hose at the heater box to keep it from slipping off. I also have scratch marks on my heater box that look similar. Anybody know where to get these? Thanks!

Just wondering if anybody had a recommendations for what type of ink to use when stamping the radiator/heater box and cooling fan? I have the stamps, just not sure what to use? Thank you.

Original moldings (Not Aftermarket) that have been professionally restored. This is a spare set that I had restored along with the other trim on the car. No scratches or dents. More pictures available on request. I am asking $75 plus shipping for the set. Thank you.

This part came off a '70 RR, but will fit many. It is intact with no missing parts and includes the under dash cable. The flap does rotate but the action is a little stiff. Probably the cable needs some attention. Priced to sell for FREE plus shipping. Wallace Wheeler Dallas, TX

These are original stainless trim pieces (not repro) that have been professionally straightened and polished. I had my grille trim set polished and had these leftover. Instead of just hanging on to them, I had them polished to sell. Hopefully someone can make good use of these. There is a right...

I just saw the announcement about the 68-69 bench seat emblems. I emailed Tony to ask if they fit the 70. He said no and the 70 RR didn't have seat emblems. There are a few people on EBay selling #2981980 claiming they are for a '70 with bench seats. Looking at he rear seat cover, there really...

I am wanting to know the correct part number for the air cleaner base for a ‘70 440+6 WITH fresh air? I have a non-fresh air base now and will cut the shield off. The air cleaner top has a part number (#2946393) and I believe that to be correct. Did the fresh air base ever get stamped with the...