Runner update

John69RR said:
Bob, do you have apicture of the drivers side engine bay where the brackets for the wiring, speedometer cable and brake lines go? I took a picture of mine but I'm not sure the brackets are in correctly. Thanks.
Click to expand...
John I hope this helps, keep in mind my brake lines come off the fender side of the master. The speedo cable also has a clip that pushes onto the frame rail just about where it goes out of the picture!
 
Looks great, Bob! :thumbsup:

So you opted to install the Accurate Exhaust Products' system yourself instead of having your local guy fab everything up? What drove your decision? Just curious...

If you're planning the break-in already does that mean you got your carbs back too?

"426 REM"...426 and your initials...???

Sorry so many questions...

:jester:
ACME
 
ACME A12 said:
Looks great, Bob! :thumbsup:

So you opted to install the Accurate Exhaust Products' system yourself instead of having your local guy fab everything up? What drove your decision? Just curious...

If you're planning the break-in already does that mean you got your carbs back too?

"426 REM"...426 and your initials...???

Sorry so many questions...

:jester:
ACME
Click to expand...
No the carbs are still getting a make over, I have another Carter I'm going to set up and block the other 4bbl off. If my throttle cable will fit I will also get it in for wheel alignment. The plate was a funny story, I went in and wanted a vanity plate 69hemi or something like that, but they will no longer issue 69 anything because it has other meanings. So the guy at dmv said how many cubic inches is it, my plates are in the 400s and he dug out this one. My wife said it means "rapid eye movement" my friend likes "remanufactured" I told the guy at the muffler shop I would get the mufflers and resonators from Accurate since all he has is Walker and glass packs, and he said if you going that far get it all and if I have trouble bring it in. He said Accurate was better as original looking than he could do.
 
69hemibeep said:
The plate was a funny story, I went in and wanted a vanity plate 69hemi or something like that, but they will no longer issue 69 anything because it has other meanings. So the guy at dmv said how many cubic inches is it, my plates are in the 400s and he dug out this one. My wife said it means "rapid eye movement" my friend likes "remanufactured".
Click to expand...

"Righteous Elephant Motor"... :yesnod:

:jester:
 
OH CRAP :toetap: :toetap: :toetap: I put 10 gallons in my tank and it shows almost a 1/4 tank :toetap: :toetap: :toetap: The first 5 got it to empty :toetap: :toetap: :toetap:
 
69hemibeep said:
OH CRAP :toetap: :toetap: :toetap: I put 10 gallons in my tank and it shows almost a 1/4 tank :toetap: :toetap: :toetap: The first 5 got it to empty :toetap: :toetap: :toetap:
Click to expand...
Join the gas guage dilema club !!!
:brickwall: :huh: :leave: :beep:
 
Ken King said:
69hemibeep said:
OH CRAP :toetap: :toetap: :toetap: I put 10 gallons in my tank and it shows almost a 1/4 tank :toetap: :toetap: :toetap: The first 5 got it to empty :toetap: :toetap: :toetap:
Click to expand...
Join the gas guage dilema club !!!
:brickwall: :huh: :leave: :beep:
Click to expand...
IF soneone sold an accuratly calibrated one they could make a mint , I heard frank babalson did so i bought one , gauge just goes up to 3/4 full when tank is full .
 
It has to be an arm adjustment because I ohm tested it and its good :crazy:
 
hmmmmm...mine have always worked fine.......... :acme:
 
69hemibeep said:
ACME A12 said:
69hemibeep said:
It has to be an arm adjustment because I ohm tested it and its good :crazy:
Click to expand...

:yesnod:


Did you like my interpretation of "REM"? :D

:jester:
Click to expand...
I forgot to pat you on the back, yes that's good :thumbsup:
Click to expand...


What, no corn dog as a reward...???!!! :lmao:

:jester:
ACME
 
u like my interpretation of "REM"? :D

:jester:[/quote]
I forgot to pat you on the back, yes that's good :thumbsup:[/quote]


What, no corn dog as a reward...???!!! :lmao:

:jester:
ACME[/quote]
hold the mustard
 
You must log in or register to reply here.
Back
Top