Search results for query: *

With Fall and Winter coming on I would like to get some heat in my car for the cool nights. My street/strip 69 roadrunner doesn't have a heater box and I was thinking of buying an inexpensive aftermarket unit and trying it out. Has anyone here gone this route and if so, which unit did you...

I'm trying to help my friend with his 68 roadrunner with 440/727 and factory hood. He currently has a Holley 4150 and Edelbrock Torker II and can only run an air filter that looks to be no more than an inch and a half tall due to it hitting the bottom of the hood. Do any of you know of an air...

I have a built 440 with 175 hp shot of nitrous and I need a reliable, somewhat quiet, performance electric fuel pump that will maintain 7 psi. I have tried two different Mallory Comp 140 pumps and two different Carter 4106's. The Mallory's are not reliable and and the Carter's advertise a lot...

I'm having trouble locating door seals/weather stripping for a friend who owns a post car. Most suppliers list it for hardtops but not post cars. My question is what are the differences in the weather stripping? Thanks!

I don't have the heater box or any of the hvac accessories/controls for my 69. I am thinking of installing a small universal unit and running heater hoses to it. I see some are available with provisions for defroster as well. I am curious if any of you have went this route for heat/defrost...

I have owned her since 1994 and was a mess when I got her home. Louise is no stranger to the strip or a late night brawl on a backroad. The engine has been an R&D project since I pulled it from a 75 New Yorker and only the block and rods are in use from the original form. I have used every...

I have a 69 road runner and I must remove the upper collar under the steering wheel that houses the turn signal switch. The snap ring is removed and the two hex head nuts are removed as well. I have pried with wood chisels wrapped in duck tape to prevent marring but the collar isn't budging...

I'm needing to souce and install a new turn signal switch with harness into my 69 with floor shifted automatic trans. What does this process involve after removing the steering wheel? Should I remove entire column or can I remove the upper collar and complete the job?

I would like to hear from Edelbrock E Street owners and get their opinions of their purchase. I would like to know if stock rockers and pushrods will suffice with these heads. Also, have you notice a seat-of-the-pants increase in performance over what was replaced? Thanks!

I have a 69 that is a street/strip car but mainly street and I'm looking to replace my 915 cast iron heads for lighter, better flowing aluminum heads. I'm not looking for max wedge ported race heads just heads that will do the job out of the box. There are several options for us Mopar guys as...

My street/strip road runner has an original style copper/brass radiator and it does a great job but I'm thinking about installing an aluminum version for the weight savings on the front end. I would like to hear from those who have an aluminum radiator and let me know what you think of it and...

I would like to know where I can find rubber floor covering instead of carpeting for my 69.

I have a problem with my electrical system that is driving me crazy. I have a trunk mounted battery that show's 12.6 volts until I connect the positive and negative battery cables to it then the voltage increases to no end. I don't have to start the car but only connect the cables and turn...

Do any of you have R/T Garage's Rev N Nator? If so, are there any issues? Thanks!

I have 175 shot of NOS and a lift off hood. I have a purge system set up that releases between the rear of hood and cowl but I never liked this position as the hood pinches my tubing somewhat. I would like to get ideas from anyone who is running NOS with purge. Thanks!!!

I have not used the vacuum advance on my street strip 440 but after reading a couple articles I'm thinking I would benefit from using it with my Holley 850. If you are using vacuum advances I would like to know whether you guys are using ported or manifold vacuum ports. Thanks!

I need to add a 6 circuit auxillary fuse block to my 69 and I'm needing suggestions on how to wire the source power in. I'm thinking I could run an 8 gauge wire from the firewall mounted starter relay but I would like to hear from others that have actually added an auxillary fuse block. I know...

Is anyone using a Denso alternator on a big block Mopar? If so, please let me know which one you have and what brackets were used. Thanks!!!!

Does anyone have experience trouble shooting an igniton delay light that was a factory installed as part of the A01 package? There is a new delay relay and light bulb installed. I have current at the relay but not at bulb. Thanks!!!!!

My 69 is equipped with the AO1 Light Package and I'm in the process of getting the ignition key light delay working. I've noticed there is another wiring connector by the key light wiring connector. The only thing I've learned thus far is that it is possibly for a headlights on buzzer. I have...